[ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 6.6.16-gentoo (root@tinker06) (gcc (Gentoo Hardened 13.2.1_p20240113-r1 p12) 13.2.1 20240113, GNU ld (Gentoo 2.40 p7) 2.40.0) #1 SMP Sat Feb 17 18:20:07 EST 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Rockchip RK3288 Asus Tinker Board S [ 0.000000] earlycon: uart0 at MMIO32 0xff690000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OF: reserved mem: 0xfe000000..0xfeffffff (16384 KiB) map non-reusable dma-unusable@fe000000 [ 0.000000] cma: Reserved 16 MiB at 0x7f000000 on node -1 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] HighMem [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] percpu: Embedded 14 pages/cpu s24788 r8192 d24364 u57344 [ 0.000000] pcpu-alloc: s24788 r8192 d24364 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Kernel command line: root=PARTUUID=cda8a22c-01 rootwait rootfstype=ext4 splash=verbose earlycon console=ttyS2,115200 console=tty1 consoleblank=0 loglevel=6 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u coherent_pool=2M init=/sbin/init net.ifnames=0 [ 0.000000] Unknown kernel command line parameters "splash=verbose", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 521984 [ 0.000000] allocated 2097152 bytes of page_ext [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 2036692K/2097152K available (15360K kernel code, 1293K rwdata, 3424K rodata, 1024K init, 569K bss, 44076K reserved, 16384K cma-reserved, 1032192K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000024] Switching to timer-based delay loop, resolution 41ns [ 0.001873] Console: colour dummy device 80x30 [ 0.001900] printk: console [tty1] enabled [ 0.001913] printk: bootconsole [uart0] disabled [ 0.001987] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.002014] CPU: Testing write buffer coherency: ok [ 0.002063] CPU0: Spectre v2: using BPIALL workaround [ 0.002076] pid_max: default: 32768 minimum: 301 [ 0.002186] LSM: initializing lsm=capability,yama,integrity [ 0.002224] Yama: becoming mindful. [ 0.002372] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002398] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.003877] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500 [ 0.005728] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.005916] Setting up static identity map for 0x100000 - 0x100060 [ 0.006156] rcu: Hierarchical SRCU implementation. [ 0.006168] rcu: Max phase no-delay instances is 1000. [ 0.007152] smp: Bringing up secondary CPUs ... [ 0.009340] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501 [ 0.009363] CPU1: Spectre v2: using BPIALL workaround [ 0.011613] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502 [ 0.011636] CPU2: Spectre v2: using BPIALL workaround [ 0.013968] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503 [ 0.013991] CPU3: Spectre v2: using BPIALL workaround [ 0.014177] smp: Brought up 1 node, 4 CPUs [ 0.014197] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.014212] CPU: All CPU(s) started in SVC mode. [ 0.015761] devtmpfs: initialized [ 0.030911] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0 [ 0.031205] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.031236] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.032155] pinctrl core: initialized pinctrl subsystem [ 0.033758] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.038959] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.039846] audit: initializing netlink subsys (disabled) [ 0.040123] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1 [ 0.041530] thermal_sys: Registered thermal governor 'step_wise' [ 0.041615] cpuidle: using governor ladder [ 0.041670] cpuidle: using governor menu [ 0.042530] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.042550] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.063901] platform ff980000.hdmi: Fixed dependency cycle(s) with /vop@ff930000/port/endpoint@0 [ 0.076665] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.077160] rockchip-gpio ff750000.gpio: probed /pinctrl/gpio@ff750000 [ 0.077685] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.078106] rockchip-gpio ff780000.gpio: probed /pinctrl/gpio@ff780000 [ 0.078588] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.078999] rockchip-gpio ff790000.gpio: probed /pinctrl/gpio@ff790000 [ 0.079470] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.079877] rockchip-gpio ff7a0000.gpio: probed /pinctrl/gpio@ff7a0000 [ 0.080605] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.081025] rockchip-gpio ff7b0000.gpio: probed /pinctrl/gpio@ff7b0000 [ 0.081503] gpio gpiochip5: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.081916] rockchip-gpio ff7c0000.gpio: probed /pinctrl/gpio@ff7c0000 [ 0.082389] gpio gpiochip6: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.082807] rockchip-gpio ff7d0000.gpio: probed /pinctrl/gpio@ff7d0000 [ 0.083273] gpio gpiochip7: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.083689] rockchip-gpio ff7e0000.gpio: probed /pinctrl/gpio@ff7e0000 [ 0.084168] gpio gpiochip8: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 0.084600] rockchip-gpio ff7f0000.gpio: probed /pinctrl/gpio@ff7f0000 [ 0.089856] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.160507] raid6: neonx8 gen() 733 MB/s [ 0.228669] raid6: neonx4 gen() 1211 MB/s [ 0.296888] raid6: neonx2 gen() 1076 MB/s [ 0.365105] raid6: neonx1 gen() 772 MB/s [ 0.433385] raid6: int32x8 gen() 230 MB/s [ 0.501566] raid6: int32x4 gen() 264 MB/s [ 0.569796] raid6: int32x2 gen() 287 MB/s [ 0.638013] raid6: int32x1 gen() 256 MB/s [ 0.638025] raid6: using algorithm neonx4 gen() 1211 MB/s [ 0.706132] raid6: .... xor() 813 MB/s, rmw enabled [ 0.706145] raid6: using neon recovery algorithm [ 0.707341] iommu: Default domain type: Translated [ 0.707358] iommu: DMA domain TLB invalidation policy: strict mode [ 0.708059] SCSI subsystem initialized [ 0.708338] usbcore: registered new interface driver usbfs [ 0.708403] usbcore: registered new interface driver hub [ 0.708468] usbcore: registered new device driver usb [ 0.708650] mc: Linux media interface: v0.10 [ 0.708727] videodev: Linux video capture interface: v2.00 [ 0.708879] pps_core: LinuxPPS API ver. 1 registered [ 0.708890] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.708919] PTP clock support registered [ 0.711359] Bluetooth: Core ver 2.22 [ 0.711422] NET: Registered PF_BLUETOOTH protocol family [ 0.711434] Bluetooth: HCI device and connection manager initialized [ 0.711451] Bluetooth: HCI socket layer initialized [ 0.711465] Bluetooth: L2CAP socket layer initialized [ 0.711496] Bluetooth: SCO socket layer initialized [ 0.711679] NetLabel: Initializing [ 0.711688] NetLabel: domain hash size = 128 [ 0.711697] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.711809] NetLabel: unlabeled traffic allowed by default [ 0.712609] clocksource: Switched to clocksource arch_sys_counter [ 0.712963] VFS: Disk quotas dquot_6.6.0 [ 0.713047] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.713226] FS-Cache: Loaded [ 0.713486] CacheFiles: Loaded [ 0.728825] NET: Registered PF_INET protocol family [ 0.729110] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.731829] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.731889] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.731977] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.732067] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.732444] TCP: Hash tables configured (established 8192 bind 8192) [ 0.732576] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.732676] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.732951] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.735757] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available [ 0.737882] Initialise system trusted keyrings [ 0.738220] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.738284] zbud: loaded [ 0.739581] SGI XFS with ACLs, security attributes, realtime, scrub, quota, fatal assert, debug enabled [ 0.905428] xor: measuring software checksum speed [ 0.915762] arm4regs : 958 MB/sec [ 0.929521] 8regs : 716 MB/sec [ 0.943273] 32regs : 715 MB/sec [ 0.950209] neon : 1426 MB/sec [ 0.950221] xor: using function: neon (1426 MB/sec) [ 0.950235] async_tx: api initialized (async) [ 0.950249] Key type asymmetric registered [ 0.950273] Asymmetric key parser 'x509' registered [ 0.950401] bounce: pool size: 64 pages [ 0.950481] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242) [ 0.950755] io scheduler mq-deadline registered [ 0.950769] io scheduler kyber registered [ 0.950812] io scheduler bfq registered [ 0.961034] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 0.961058] dma-pl330 ff250000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 [ 0.962300] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 0.962322] dma-pl330 ffb20000.dma-controller: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10 [ 0.964771] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled [ 0.969595] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 47, base_baud = 1500000) is a 16550A [ 0.969943] serial serial0: tty port ttyS0 registered [ 0.971674] ff190000.serial: ttyS1 at MMIO 0xff190000 (irq = 48, base_baud = 1500000) is a 16550A [ 0.973630] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 49, base_baud = 1500000) is a 16550A [ 0.973823] printk: console [ttyS2] enabled [ 1.156000] ff1b0000.serial: ttyS3 at MMIO 0xff1b0000 (irq = 50, base_baud = 1500000) is a 16550A [ 1.158020] ff1c0000.serial: ttyS4 at MMIO 0xff1c0000 (irq = 51, base_baud = 1500000) is a 16550A [ 1.169418] usbcore: registered new interface driver udl [ 1.170652] brd: module loaded [ 1.180027] loop: module loaded [ 1.182216] rockchip-spi ff130000.spi: cs1 >= max 1 [ 1.187776] spi_master spi2: spi_device register error /spi@ff130000/spidev@1 [ 1.195826] spi_master spi2: Failed to create SPI device for /spi@ff130000/spidev@1 [ 1.207124] tun: Universal TUN/TAP device driver, 1.6 [ 1.207432] CAN device driver interface [ 1.209842] usbcore: registered new interface driver rt2500usb [ 1.209900] usbcore: registered new interface driver rt73usb [ 1.209953] usbcore: registered new interface driver rt2800usb [ 1.210002] usbcore: registered new interface driver rndis_wlan [ 1.210060] usbcore: registered new interface driver cdc_ether [ 1.210112] usbcore: registered new interface driver rndis_host [ 1.210784] dwc2 ff540000.usb: supply vusb_d not found, using dummy regulator [ 1.219016] dwc2 ff540000.usb: supply vusb_a not found, using dummy regulator [ 1.285030] dwc2 ff540000.usb: DWC OTG Controller [ 1.285085] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1 [ 1.285132] dwc2 ff540000.usb: irq 58, io mem 0xff540000 [ 1.285477] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06 [ 1.285502] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.285520] usb usb1: Product: DWC OTG Controller [ 1.285534] usb usb1: Manufacturer: Linux 6.6.16-gentoo dwc2_hsotg [ 1.285548] usb usb1: SerialNumber: ff540000.usb [ 1.286385] hub 1-0:1.0: USB hub found [ 1.286450] hub 1-0:1.0: 1 port detected [ 1.287419] dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator [ 1.295660] dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator [ 1.318988] dwc2 ff580000.usb: dwc2_core_reset: HANG! Soft Reset timeout GRSTCTL_CSFTRST [ 1.328109] dwc2: probe of ff580000.usb failed with error -16 [ 1.337492] usbcore: registered new interface driver usb-storage [ 1.338138] ehci-platform ff500000.usb: EHCI Host Controller [ 1.338485] mousedev: PS/2 mouse device common for all mice [ 1.338501] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 2 [ 1.339067] usbcore: registered new interface driver iforce [ 1.339152] usbcore: registered new interface driver xpad [ 1.339285] usbcore: registered new interface driver usbtouchscreen [ 1.339291] ehci-platform ff500000.usb: irq 60, io mem 0xff500000 [ 1.339848] i2c_dev: i2c /dev entries driver [ 1.343893] i2c 0-001b: Fixed dependency cycle(s) with /i2c@ff650000/pmic@1b/regulators/DCDC_REG4 [ 1.352637] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00 [ 1.352963] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06 [ 1.352988] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.353006] usb usb2: Product: EHCI Host Controller [ 1.353020] usb usb2: Manufacturer: Linux 6.6.16-gentoo ehci_hcd [ 1.353034] usb usb2: SerialNumber: ff500000.usb [ 1.354186] hub 2-0:1.0: USB hub found [ 1.354258] hub 2-0:1.0: 1 port detected [ 1.358657] vdd10_lcd: Bringing 800000uV into 1000000-1000000uV [ 1.366567] rk808-rtc rk808-rtc.2.auto: registered as rtc0 [ 1.367149] rk808-rtc rk808-rtc.2.auto: setting system clock to 2013-01-18T08:50:34 UTC (1358499034) [ 1.371774] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 1.372230] Bluetooth: HCI UART driver ver 2.3 [ 1.372248] Bluetooth: HCI UART protocol H4 registered [ 1.372261] Bluetooth: HCI UART protocol ATH3K registered [ 1.372342] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 1.372503] Bluetooth: HCI UART protocol Broadcom registered [ 1.372568] usbcore: registered new interface driver bfusb [ 1.372691] usbcore: registered new interface driver btusb [ 1.373196] dw-apb-uart ff180000.serial: failed to request DMA [ 1.374060] sdhci: Secure Digital Host Controller Interface driver [ 1.379783] sdhci: Copyright(c) Pierre Ossman [ 1.379795] Synopsys Designware Multimedia Card Interface Driver [ 1.380444] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.382103] dwmmc_rockchip ff0c0000.mmc: IDMAC supports 32-bit address mode. [ 1.382128] ledtrig-cpu: registered to indicate activity on CPUs [ 1.382319] hid: raw HID events driver (C) Jiri Kosina [ 1.382596] dwmmc_rockchip ff0c0000.mmc: Using internal DMA controller. [ 1.382623] dwmmc_rockchip ff0c0000.mmc: Version ID is 270a [ 1.382692] dwmmc_rockchip ff0c0000.mmc: DW MMC controller at irq 76,32 bit host data width,256 deep fifo [ 1.382961] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. [ 1.383219] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. [ 1.383243] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a [ 1.383271] usbcore: registered new interface driver usbhid [ 1.383290] usbhid: USB HID core driver [ 1.383318] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 77,32 bit host data width,256 deep fifo [ 1.383426] mmc_host mmc0: card is polling. [ 1.383994] dwmmc_rockchip ff0d0000.mmc: allocated mmc-pwrseq [ 1.384018] mmc_host mmc1: card is non-removable. [ 1.384062] dwmmc_rockchip ff0f0000.mmc: IDMAC supports 32-bit address mode. [ 1.384332] dwmmc_rockchip ff0f0000.mmc: Using internal DMA controller. [ 1.384355] dwmmc_rockchip ff0f0000.mmc: Version ID is 270a [ 1.384425] dwmmc_rockchip ff0f0000.mmc: DW MMC controller at irq 78,32 bit host data width,256 deep fifo [ 1.384719] mmc_host mmc2: card is non-removable. [ 1.387965] NET: Registered PF_INET6 protocol family [ 1.389929] Segment Routing with IPv6 [ 1.390011] In-situ OAM (IOAM) with IPv6 [ 1.390150] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.391908] NET: Registered PF_PACKET protocol family [ 1.391961] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.391976] can: controller area network core [ 1.392048] NET: Registered PF_CAN protocol family [ 1.392243] Bluetooth: RFCOMM TTY layer initialized [ 1.392268] Bluetooth: RFCOMM socket layer initialized [ 1.392302] Bluetooth: RFCOMM ver 1.11 [ 1.392327] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.392347] Bluetooth: HIDP socket layer initialized [ 1.392538] 8021q: 802.1Q VLAN Support v1.8 [ 1.392580] lib80211: common routines for IEEE802.11 drivers [ 1.392643] lib80211_crypt: registered algorithm 'NULL' [ 1.392666] lib80211_crypt: registered algorithm 'WEP' [ 1.392678] lib80211_crypt: registered algorithm 'CCMP' [ 1.392689] lib80211_crypt: registered algorithm 'TKIP' [ 1.392743] Key type dns_resolver registered [ 1.396268] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 1.396682] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 1.397707] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 1.397851] ThumbEE CPU extension supported. [ 1.397874] Registering SWP/SWPB emulation handler [ 1.420350] registered taskstats version 1 [ 1.420697] Loading compiled-in X.509 certificates [ 1.425799] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 1.426119] mmc1: error -84 whilst initialising SDIO card [ 1.432326] dwmmc_rockchip ff0d0000.mmc: card claims to support voltages below defined range [ 1.436846] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0) [ 1.445796] mmc1: error -110 whilst initialising MMC card [ 1.447071] zswap: loaded using pool zstd/z3fold [ 1.462309] Key type .fscrypt registered [ 1.463653] mmc_host mmc0: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0) [ 1.466133] mmc_host mmc1: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0) [ 1.466757] Key type fscrypt-provisioning registered [ 1.468465] Btrfs loaded, zoned=no, fsverity=no [ 1.492712] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0) [ 1.500685] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 1.501896] mmc1: new high speed SDIO card at address 0001 [ 1.502654] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found [ 1.502793] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock [ 1.503015] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input). [ 1.503037] rk_gmac-dwmac ff290000.ethernet: TX delay(0x30). [ 1.503054] rk_gmac-dwmac ff290000.ethernet: RX delay(0x10). [ 1.503076] rk_gmac-dwmac ff290000.ethernet: integrated PHY? (no). [ 1.503141] rk_gmac-dwmac ff290000.ethernet: clock input from PHY [ 1.508167] rk_gmac-dwmac ff290000.ethernet: init for RGMII [ 1.508493] rk_gmac-dwmac ff290000.ethernet: User ID: 0x10, Synopsys ID: 0x35 [ 1.508520] rk_gmac-dwmac ff290000.ethernet: DWMAC1000 [ 1.508536] rk_gmac-dwmac ff290000.ethernet: DMA HW capability register supported [ 1.508549] rk_gmac-dwmac ff290000.ethernet: RX Checksum Offload Engine supported [ 1.508561] rk_gmac-dwmac ff290000.ethernet: COE Type 2 [ 1.508574] rk_gmac-dwmac ff290000.ethernet: TX Checksum insertion supported [ 1.508625] rk_gmac-dwmac ff290000.ethernet: Wake-Up On Lan supported [ 1.508733] rk_gmac-dwmac ff290000.ethernet: Normal descriptors [ 1.508749] rk_gmac-dwmac ff290000.ethernet: Ring mode enabled [ 1.508762] rk_gmac-dwmac ff290000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 1.543552] mmc_host mmc2: Bus speed (slot 0) = 187500Hz (slot req 187500Hz, actual 187500HZ div = 0) [ 1.583173] mmc2: Failed to initialize a non-removable card [ 1.592648] usb 1-1: new high-speed USB device number 2 using dwc2 [ 1.616642] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 1.802164] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98 [ 1.802191] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.802209] usb 1-1: Product: USB2.0 Hub [ 1.803175] hub 1-1:1.0: USB hub found [ 1.803526] hub 1-1:1.0: 4 ports detected [ 1.974379] usb 2-1: config 1 has an invalid interface number: 255 but max is 6 [ 1.982637] usb 2-1: config 1 has no interface number 6 [ 1.990111] usb 2-1: New USB device found, idVendor=0bda, idProduct=481a, bcdDevice= 0.00 [ 1.990137] usb 2-1: New USB device strings: Mfr=3, Product=1, SerialNumber=2 [ 1.990154] usb 2-1: Product: USB Audio [ 1.990168] usb 2-1: Manufacturer: Generic [ 1.990181] usb 2-1: SerialNumber: 201405280001 [ 1.997930] input: Generic USB Audio Consumer Control as /devices/platform/ff500000.usb/usb2/2-1/2-1:1.255/0003:0BDA:481A.0001/input/input0 [ 2.057113] input: Generic USB Audio as /devices/platform/ff500000.usb/usb2/2-1/2-1:1.255/0003:0BDA:481A.0001/input/input1 [ 2.057835] hid-generic 0003:0BDA:481A.0001: input,hiddev96,hidraw0: USB HID v1.11 Device [Generic USB Audio] on usb-ff500000.usb-1/input255 [ 2.092642] usb 1-1.1: new high-speed USB device number 3 using dwc2 [ 2.144659] Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723 [ 2.148936] Bluetooth: hci0: RTL: rom_version status=0 version=1 [ 2.148959] Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin [ 2.148977] Loading firmware: rtl_bt/rtl8723bs_fw.bin [ 2.154769] bluetooth hci0: Direct firmware load for rtl_bt/rtl8723bs_fw.bin failed with error -2 [ 2.164778] Bluetooth: hci0: RTL: firmware file rtl_bt/rtl8723bs_fw not found [ 2.195779] usb 1-1.1: New USB device found, idVendor=0bc2, idProduct=ab21, bcdDevice= 1.43 [ 2.195806] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.195824] usb 1-1.1: Product: BUP Slim BK [ 2.195838] usb 1-1.1: Manufacturer: Seagate [ 2.195850] usb 1-1.1: SerialNumber: NA7NTXEG [ 2.196729] usb 1-1.1: The driver for the USB controller dwc2_hsotg does not support scatter-gather which is [ 2.207779] usb 1-1.1: required by the UAS driver. Please try an other USB controller if you wish to use UAS. [ 2.218912] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 2.219878] scsi host0: usb-storage 1-1.1:1.0 [ 2.244677] dwmmc_rockchip ff0c0000.mmc: Successfully tuned phase to 159 [ 2.244720] mmc0: new ultra high speed SDR104 SDXC card at address 5048 [ 2.245728] mmcblk0: mmc0:5048 SD64G 58.0 GiB [ 2.248892] mmcblk0: p1 [ 2.300645] usb 1-1.2: new high-speed USB device number 4 using dwc2 [ 2.401489] usb 1-1.2: New USB device found, idVendor=aaaa, idProduct=8816, bcdDevice=13.08 [ 2.401516] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.401534] usb 1-1.2: Product: MXT USB Device [ 2.401548] usb 1-1.2: Manufacturer: MXTronics [ 2.401561] usb 1-1.2: SerialNumber: 150101v01 [ 2.402777] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 2.403513] scsi host1: usb-storage 1-1.2:1.0 [ 2.484641] usb 1-1.4: new full-speed USB device number 5 using dwc2 [ 2.573672] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 2.573700] mdio_bus stmmac-0:01: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:01, irq=POLL) [ 2.580751] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.587854] usb 1-1.4: New USB device found, idVendor=046d, idProduct=c534, bcdDevice=29.01 [ 2.589496] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.589517] usb 1-1.4: Product: USB Receiver [ 2.589531] usb 1-1.4: Manufacturer: Logitech [ 2.593602] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.594234] input: Logitech USB Receiver as /devices/platform/ff540000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:046D:C534.0002/input/input2 [ 2.602653] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 2.610840] Loading firmware: regulatory.db [ 2.612682] clk: Disabling unused clocks [ 2.615662] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.625405] cfg80211: failed to load regulatory.db [ 2.657686] hid-generic 0003:046D:C534.0002: input,hidraw1: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-ff540000.usb-1.4/input0 [ 2.666132] input: Logitech USB Receiver Mouse as /devices/platform/ff540000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C534.0003/input/input3 [ 2.666885] input: Logitech USB Receiver Consumer Control as /devices/platform/ff540000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C534.0003/input/input4 [ 2.725060] input: Logitech USB Receiver System Control as /devices/platform/ff540000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C534.0003/input/input5 [ 2.725767] hid-generic 0003:046D:C534.0003: input,hiddev97,hidraw2: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-ff540000.usb-1.4/input1 [ 2.728431] md: Waiting for all devices to be available before autodetect [ 2.728446] md: If you don't use raid, use raid=noautodetect [ 2.730672] md: Autodetecting RAID arrays. [ 2.730688] md: autorun ... [ 2.730697] md: ... autorun DONE. [ 2.739653] EXT4-fs (mmcblk0p1): mounted filesystem 52e543ff-99d6-4974-9fed-cac7c49f0d80 ro with ordered data mode. Quota mode: none. [ 2.739735] VFS: Mounted root (ext4 filesystem) readonly on device 179:1. [ 2.743831] devtmpfs: mounted [ 2.745740] Freeing unused kernel image (initmem) memory: 1024K [ 2.753127] Run /sbin/init as init process [ 2.753143] with arguments: [ 2.753151] /sbin/init [ 2.753160] with environment: [ 2.753168] HOME=/ [ 2.753176] TERM=linux [ 2.753184] splash=verbose [ 3.238520] scsi 0:0:0:0: Direct-Access Seagate BUP Slim BK 0143 PQ: 0 ANSI: 6 [ 3.249897] sd 0:0:0:0: [sda] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB) [ 3.259712] sd 0:0:0:0: [sda] Write Protect is off [ 3.265182] sd 0:0:0:0: [sda] Mode Sense: 2b 00 10 08 [ 3.266029] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 3.434087] scsi 1:0:0:0: Direct-Access MXT-USB Storage Device 1501 PQ: 0 ANSI: 0 CCS [ 3.447542] sd 1:0:0:0: [sdb] 121634816 512-byte logical blocks: (62.3 GB/58.0 GiB) [ 3.456702] sd 1:0:0:0: [sdb] Write Protect is off [ 3.462122] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 3.462658] sd 1:0:0:0: [sdb] No Caching mode page found [ 3.468669] sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 3.481175] sdb: sdb1 [ 3.481662] sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 3.585294] sda: sda1 [ 3.585740] sd 0:0:0:0: [sda] Attached SCSI disk [ 3.596656] random: crng init done [ 12.775613] platform display-subsystem: deferred probe pending [ 14.279391] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 500000 KHz, changing to: 600000 KHz [ 14.344720] dw_wdt ff800000.watchdog: No valid TOPs array specified [ 14.399575] rk3288-crypto ff8a0000.crypto: will run requests pump with realtime priority [ 14.399603] rk3288-crypto ff8a0000.crypto: Register ecb(aes) as ecb-aes-rk [ 14.399639] rk3288-crypto ff8a0000.crypto: Register cbc(aes) as cbc-aes-rk [ 14.399648] rk3288-crypto ff8a0000.crypto: Register ecb(des) as ecb-des-rk [ 14.399656] rk3288-crypto ff8a0000.crypto: Register cbc(des) as cbc-des-rk [ 14.399664] rk3288-crypto ff8a0000.crypto: Register ecb(des3_ede) as ecb-des3-ede-rk [ 14.399673] rk3288-crypto ff8a0000.crypto: Register cbc(des3_ede) as cbc-des3-ede-rk [ 14.399680] rk3288-crypto ff8a0000.crypto: Register sha1 as rk-sha1 [ 14.399690] rk3288-crypto ff8a0000.crypto: Register sha256 as rk-sha256 [ 14.399699] rk3288-crypto ff8a0000.crypto: Register md5 as rk-md5 [ 14.411014] usbcore: registered new interface driver uas [ 14.427620] r8723bs: module is from the staging directory, the quality is unknown, you have been warned. [ 14.429130] r8723bs: unknown parameter 'rtw_enusbss' ignored [ 14.430389] pnetdev = 475ef676 [ 14.465322] panfrost ffa30000.gpu: clock rate = 400000000 [ 14.467723] panfrost ffa30000.gpu: mali-t760 id 0x750 major 0x0 minor 0x0 status 0x1 [ 14.467743] panfrost ffa30000.gpu: features: 00000000,00000407, issues: 00000000,24040400 [ 14.467753] panfrost ffa30000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 [ 14.467760] panfrost ffa30000.gpu: shader_present=0xf l2_present=0x1 [ 14.472232] [drm] Initialized panfrost 1.2.0 20180908 for ffa30000.gpu on minor 0 [ 14.477576] input: gpio-keys as /devices/platform/gpio-keys/input/input8 [ 14.484104] rockchip-rga ff920000.rga: HW Version: 0x00.00 [ 14.487672] rockchip-rga ff920000.rga: Registered rockchip-rga as /dev/video0 [ 14.498373] hantro-vpu ff9a0000.video-codec: Adding to iommu group 3 [ 14.505710] hantro-vpu ff9a0000.video-codec: registered rockchip,rk3288-vpu-enc as /dev/video1 [ 14.506274] hantro-vpu ff9a0000.video-codec: registered rockchip,rk3288-vpu-dec as /dev/video2 [ 14.554481] logitech-djreceiver 0003:046D:C534.0002: hidraw1: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-ff540000.usb-1.4/input0 [ 14.595251] usb 2-1: 4:11: invalid format type 0x2001 is detected, processed as PCM [ 14.770474] logitech-djreceiver 0003:046D:C534.0003: hiddev97,hidraw2: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-ff540000.usb-1.4/input1 [ 14.831181] logitech-djreceiver 0003:046D:C534.0003: device of type eQUAD nano Lite (0x0a) connected on slot 1 [ 14.833178] logitech-djreceiver 0003:046D:C534.0003: device of type eQUAD nano Lite (0x0a) connected on slot 2 [ 14.836883] input: Logitech Wireless Keyboard PID:4075 Keyboard as /devices/platform/ff540000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C534.0003/0003:046D:4075.0004/input/input9 [ 14.842990] hid-generic 0003:046D:4075.0004: input,hidraw3: USB HID v1.11 Keyboard [Logitech Wireless Keyboard PID:4075] on usb-ff540000.usb-1.4/input1:1 [ 14.846070] input: Logitech Wireless Mouse PID:4091 Mouse as /devices/platform/ff540000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C534.0003/0003:046D:4091.0005/input/input14 [ 14.857611] hid-generic 0003:046D:4091.0005: input,hidraw4: USB HID v1.11 Mouse [Logitech Wireless Mouse PID:4091] on usb-ff540000.usb-1.4/input1:2 [ 15.099581] input: Logitech Wireless Keyboard PID:4075 as /devices/platform/ff540000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C534.0003/0003:046D:4075.0004/input/input18 [ 15.100058] logitech-hidpp-device 0003:046D:4075.0004: input,hidraw3: USB HID v1.11 Keyboard [Logitech Wireless Keyboard PID:4075] on usb-ff540000.usb-1.4/input1:1 [ 15.155755] input: Logitech Wireless Mouse as /devices/platform/ff540000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C534.0003/0003:046D:4091.0005/input/input19 [ 15.156634] logitech-hidpp-device 0003:046D:4091.0005: input,hidraw4: USB HID v1.11 Mouse [Logitech Wireless Mouse] on usb-ff540000.usb-1.4/input1:2 [ 16.675507] usbcore: registered new interface driver snd-usb-audio [ 21.065577] EXT4-fs (mmcblk0p1): re-mounted 52e543ff-99d6-4974-9fed-cac7c49f0d80 r/w. Quota mode: none. [ 21.120669] EXT4-fs (mmcblk0p1): re-mounted 52e543ff-99d6-4974-9fed-cac7c49f0d80 r/w. Quota mode: none. [ 21.734690] EXT4-fs (dm-3): mounted filesystem 9123b248-5a7d-4470-81a2-e52876a2dff2 r/w with ordered data mode. Quota mode: none. [ 21.837744] EXT4-fs (dm-1): mounted filesystem 77f3d7d4-95c0-4da8-8377-1aeddbd37c40 r/w with ordered data mode. Quota mode: none. [ 45.015633] rk_gmac-dwmac ff290000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 45.019830] rk_gmac-dwmac ff290000.ethernet eth0: PHY [stmmac-0:00] driver [Generic PHY] (irq=POLL) [ 45.028623] rk_gmac-dwmac ff290000.ethernet eth0: No Safety Features support found [ 45.028646] rk_gmac-dwmac ff290000.ethernet eth0: PTP not supported by HW [ 45.031305] rk_gmac-dwmac ff290000.ethernet eth0: configuring for phy/rgmii link mode [ 45.037850] rtl8723bs: acquire FW from file:rtlwifi/rtl8723bs_nic.bin [ 45.037870] Loading firmware: rtlwifi/rtl8723bs_nic.bin [ 46.416728] warning: `grep' uses wireless extensions which will stop working for Wi-Fi 7 hardware; use nl80211 [ 49.125394] rk_gmac-dwmac ff290000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx